Where silica turns up on a construction site
Most building materials contain crystalline silica. WorkSafe Victoria's guidance gives typical ranges: concrete is often under 30 per cent, bricks around 5 to 15 per cent, ceramic tiles 5 to 45 per cent and porcelain 14 to 18 per cent. Engineered stone can be far higher. Content varies by product, so check the safety data sheet.
The dust is made when you process the material. The common tasks on a SWMS are:
- checkSaw cutting concrete slabs, pavers, kerbs and blocks
- checkCore drilling and chasing walls for services
- checkGrinding and scabbling concrete floors and edges
- checkCutting tiles, bricks and masonry with angle grinders or wet saws
- checkCutting or drilling fibre cement sheet where the product contains silica
- checkDemolition, crushing and jackhammering of concrete and masonry
- checkDry sweeping or blowing down dust afterwards (a common and avoidable exposure)
The exposure standard
The workplace exposure standard for respirable crystalline silica is 0.05 mg/m³ as an 8-hour time-weighted average. SafeWork NSW describes the duty not to exceed it as absolute, not qualified by "reasonably practicable". Longer shifts need an adjusted figure: WorkSafe Victoria gives 0.035 mg/m³ for a 10-hour day, and recommends keeping exposure at or below 0.02 mg/m³.
A lower national value has been researched by Safe Work Australia but has not been adopted, partly because current sampling methods cannot measure it reliably. Check your regulator's current figure before quoting a number in your SWMS. If you do not know whether workers are over the standard, air monitoring by a competent person such as an occupational hygienist is the way to find out.
The engineered stone ban: what is still allowed
From 1 July 2024, the manufacture, supply, processing and installation of engineered stone benchtops, panels and slabs is prohibited in every state and territory. In the model WHS Regulations this sits in Chapter 8A (the prohibition is r 529D in the model numbering; check your state's version). Engineered stone is defined as an artificial product with 1 per cent or more crystalline silica, made by combining natural stone materials with resins, water or pigments. Concrete, bricks, pavers, ceramic tiles, grout, mortar, render, plasterboard, porcelain, sintered stone and roof tiles are excluded from that definition.
Work on stone that is already installed can still be done, but only as controlled processing:
- checkRemoving, repairing or making minor modifications to installed engineered stone
- checkDisposing of engineered stone, installed or not
- checkResearch, analysis, sampling and identification
- checkUnder the harmonised laws, the WHS regulator must be notified before processing for removal, repair, modification or disposal, using the approved form
- checkVictoria: WorkSafe Victoria says no notification is needed for legacy work, but the existing silica controls and high risk crystalline silica work rules apply
Controlled processing of all silica materials
From 1 September 2024, the harmonised states extended the rules to processing any crystalline silica substance, meaning material with at least 1 per cent crystalline silica. Processing (cutting, grinding, drilling, sanding, crushing or polishing with a power tool or plant) must be controlled. In practice that means risks are minimised so far as reasonably practicable, at least one engineering control is used, and RPE is worn where risk remains. WorkSafe Queensland lists the engineering options as:
- checkIsolating workers from the dust, or a fully enclosed operator cabin with filtered air
- checkEffective wet dust suppression with a continuous water feed
- checkEffective on-tool extraction
- checkEffective local exhaust ventilation
High risk processing and where the SWMS fits
Processing must be risk assessed to decide if it is high risk, meaning reasonably likely to harm health. If you cannot tell, treat it as high risk. High risk processing needs a silica risk control plan, accredited or regulator-approved silica training for exposed workers, and consideration of air and health monitoring. WorkSafe Queensland notes that for high risk construction work, the SWMS is used instead of a separate silica risk control plan, so your SWMS has to carry that detail.
Victoria runs its own scheme under the OHS Regulations 2017. High risk crystalline silica work needs a hazard control statement, which can be built into the SWMS where the work is also high risk construction work.
What good silica controls look like in a SWMS
- checkName the tool and the control: for example "150 mm grinder with shroud connected to H-class vacuum"
- checkWater suppression with a continuous feed, and the slurry captured before it dries
- checkOn-tool extraction connected to an M or H class vacuum, emptied in a way that does not release dust
- checkRPE of at least P2, individually fit tested, clean shaven for tight-fitting masks, or a loose-fitting PAPR
- checkNo dry sweeping, compressed air or high-pressure water for clean-up; HEPA vacuum or wet methods only
- checkExclusion zone so other trades are not breathing your dust
- checkSlurry and dust kept out of stormwater, and waste bagged and labelled
- checkHealth monitoring arranged by the PCBU where there is a significant risk
Health monitoring
Where workers are at significant risk from silica dust, the PCBU must arrange and pay for health monitoring supervised by a registered medical practitioner. SafeWork NSW lists the minimum for engineered stone work as work and medical history, exposure records, a respiratory questionnaire, spirometry and a chest X-ray, with low-dose CT as an option. Reports are confidential and must be kept for at least 30 years.
Common questions
Is cutting concrete banned like engineered stone?
No. Concrete, bricks, pavers and ceramic tiles are not engineered stone. You can still cut them, but processing must be controlled with water, on-tool extraction or ventilation, plus RPE where risk remains.
Can I still remove an engineered stone benchtop?
Yes. Removal, repair, minor modification and disposal of installed stone are allowed as controlled processing. In the harmonised states you must notify the regulator first. Victoria does not require notification.
What is the silica exposure standard in Australia?
0.05 mg/m³ as an 8-hour time-weighted average. It must be adjusted down for longer shifts. Check your regulator for the current figure.
Is a P2 mask enough for silica?
Only as the last line of defence, fit tested and worn clean shaven, alongside water or on-tool extraction. RPE on its own does not meet the controlled processing rules.
Sources
- Safe Work Australia — Amendments to implement the engineered stone ban (from 1 July 2024)
- Safe Work Australia — Stronger regulation of crystalline silica substances from 1 September 2024
- WorkSafe Queensland — Regulation on processing crystalline silica substances
- SafeWork NSW — Engineered stone code of practice: specific duties (exposure standard and health monitoring)
- Safe Work Australia — Research into a lower workplace exposure standard for respirable crystalline silica
- Work Health and Safety Amendment (Engineered Stone) Regulations 2024 (Tas) — mirrors the model Chapter 8A amendments
- WorkSafe Victoria — Construction: preventing exposure to crystalline silica dust
- WorkSafe Victoria — Engineered stone ban now in force
General information only, current at the date above. Legislation changes — confirm requirements with your state regulator. As the PCBU you remain responsible for your SWMS.
See a finished SWMS first
A complete 14-page example as a Word document, emailed to you.