SWMS for Plumbing
Plumbing SWMS for trenches, gas, roofs and confined spaces.
Plumbing touches more high-risk categories than most trades: trenching deeper than 1.5 m, work near gas mains, confined pits and tanks, roof plumbing at height and asbestos in old cement-sheet pipework. Your SWMS has to say how each one is controlled on this site. Describe the job and the platform writes it in the order you do the work.
- First SWMS free, no card
- Word document in about 5 minutes
- $19.99 inc. GST after that, 3 revisions included
High-risk construction work this SWMS usually covers
- 7 Trench or shaft deeper than 1.5 m, or a tunnel
- 9 Work on or near pressurised gas mains or piping
- 6 Work in or near a confined space
- 1 Risk of a fall more than 2 m
- 4 Likely disturbance of asbestos
- 15 Movement of powered mobile plant
Categories per the model WHS Regulations, s 291 (OHS Regulations 2017, r 322 in Victoria). You confirm which apply when you describe the job.
What goes in it
Typical activities, in the order you do the work
- Site arrival, induction and service location (Before You Dig Australia enquiry, locator and pothole)
- Excavation and trench support — benching, battering or shoring; spoil set back from the edge
- Pipe laying, jointing and backfill
- Gas fitting, purging and testing
- Roof plumbing — access, edge protection and work near skylights
- Hot works for brazing and soldering
- Pressure testing, commissioning and handover
Each activity gets its hazards, the controls in hierarchy order (eliminate, substitute, isolate, engineering, administrative, PPE), the residual risk rating and who is responsible.
Key hazards and how they are controlled
Written as controls, not slogans
Trench collapse and engulfment
Ground assessment, shoring, benching or battering for trenches 1.5 m or deeper, safe ladder access close to the work, no one in an unsupported trench
Striking underground services
Before You Dig plans, electronic locating, pot-holing by hand or vacuum before mechanical digging
Gas leak, fire or explosion
Isolate and purge, gas detection, no ignition sources, licensed gasfitter, test before commissioning
Falls from roofs and through brittle sheeting
Edge protection or harness system, walkways over brittle areas, skylight covers
Who asks for it
Set out the way builders' safety teams expect
Builders and civil contractors ask for it before any trench is opened; gas network operators, strata managers and commercial clients ask for it before gas or roof work.
- verifiedSite address, PCBU, supervisor and contact details on the front page
- verifiedHRCW checklist ticked for the work actually being done
- verifiedYour state's WHS legislation and Codes of Practice referenced
- verified5×5 risk matrix, hierarchy of controls, emergency response and nearest hospital
- verifiedConsultation and sign-on sheet for the crew
See the output first
Email me a sample SWMS
A full 14-page example as a Word document, so you can see exactly what you'll get before you start.
Questions about a plumbing SWMS
Is a trench less than 1.5 m still high-risk work?
Trenches deeper than 1.5 m are HRCW in their own right. Shallower trenches can still be HRCW if other categories apply — for example work near pressurised gas mains or in or near a confined space — and the SWMS still has to control collapse and service-strike risk.
Can I add my gas licence and other details?
Yes. The SWMS lists the licences and training required and you confirm the names and numbers when you review it.
How much does it cost?
Your first SWMS is free. Every SWMS after that is $19.99 inc. GST, paid before it is generated, with up to 3 revisions included. No subscription.
Related: Excavation SWMS · Roofing SWMS · Electrical SWMS
Builder asked for a SWMS by tomorrow?
Describe the job tonight and it's in your inbox in minutes. First one free.
Start my free plumbing SWMS arrow_forward